Water Level Indicator

Water Level Indicator Circuit

Versatile circuit which indicates the level of water in a tank. This circuit produces alarm when water level is below the lowest level L1 and also when water just touches the highest level L12. The circuit is designed to display 12 different levels. However, these display levels can be increased or decreased depending upon the level resolution required. This can be done by increasing or decreasing the number of level detector metal strips (L1 to L12) and their associated components. In the circuit, diodes D1, D2 and
D13 form half-wave rectifiers. The rectified output is filtered using capacitors C1 through C3 respectively. Initially, when water level is below strip L1, the mains supply frequency oscillations are not transferred to diode D1. Thus its output is low and LED1 does not glow. Also, since base voltage of transistor T1 is low, it is in cut-off state and its collector voltage is high, which enables tone generating IC1 (UM66) and alarm is sounded. When water just touches level detector strip L1, the supply frequency oscillations are transferred to diode D1. It rectifies the supply voltage and a positive DC voltage develops across capacitor C1, which lights up LED1. At the same time base voltage for transistor T1 becomes high, which makes it forward biased and its collector voltage falls to near-ground potential. This disables IC1 (UM66) and alarm cannot be sounded. Depending upon quantity of water present in the tank, corresponding level indicating LEDs glow. It thus displays intermediate water levels in the tank in bar-graph style. When water in the tank just touches the highest level detector strip L12, the DC voltage is developed across capacitor C2. This enables tone generating IC1 (UM66) and alarm is again sounded.

Read More

Water Level Alarm (Alarm Ketinggian Air)

This circuit will produce an audible alarm when the water level reaches a preset level.The circuit can be powered of a 3V battery and is very handy to use.


The circuit is based on an astable multivibrator wired around IC1 (NE 555).The operating frequency of the astable multivibrator here will depend on capacitor C1, resistances R1,R2 and the resistance across the probes A&B.When there is no water up to the probes,they will be open and so the multivibrator will not produce oscillations and the buzzer will not beep.When there is water up to the level of probes,some current will pass through the water,the circuit will be closed to some extend,and the IC will start producing oscillations in a frequency proportional to the value of C1,R1,R2 and the resistance of water across the probes.The buzzer will beep to indicate the presence of water up to the level of the sensing probes.


Notes

• The circuit can be powered of a 3V battery.
• Assemble the circuit on a good quality PCB or common board.
• The probes can be made of two insulated copper Aluminiun wires.
• Place the probes at the position where you have to sense the level.

Read More

Water Level Indicator (Indikator Level Air)

This circuit not only indicates the amount of water present in the overhead tank but also gives an alarm when the tank is full.
The circuit uses the widely available CD4066, bilateral switch CMOS IC to indicate the water level through LEDs.


When the water is empty the wires in the tank are open circuited and the 180K resistors pulls the switch low
hence opening the switch and LEDs are OFF. As the water starts filling up, first the wire in the tank connected to S1 and the + supply are shorted by water. This closes the switch S1 and turns the LED1 ON. As the water continues to fill the tank, the LEDs2 , 3 and 4 light up gradually.
The no. of levels of indication can be increased to 8 if 2 CD4066 ICs are used in a similar fashion.

When the water is full, the base of the transistor BC148 is pulled high by the water and this saturates the transistor, turning the buzzer ON. The SPST switch has to be opened to turn the buzzer OFF.
Remember to turn the switch ON while pumping water otherwise the buzzer will not sound!


Rangkaian ini cukup sederhana dan murah tapi sangat bermanfaat ketika kita ingin mengetahui level air di tabung penampungan dan ketika air sudah penuh maka buzzer pun berbunyi utk mengingatkan kita..

Read More